View ATX0200_8362386.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification model no. ATX0200 this specification describes the requirements of 300w,350w,400w,450w,500w, 550w,600w with active p.f.c switching power supply with an atx form-factor,+5v standby voltage,fan control,atx 12v power supply version 2.3, remote on/off control,dual line input capability and forced air cooling characteristics. ? 1.0 table1. ac input requirements the input voltage, current, and frequency requirements for continuous operation are stated below. (300w) parameter min nom. max unit v in 90 100 - 240 264 vacrms v in frequency 47 60 50 63 hz i in 63 a (350w) parameter min nom. max unit v in 90 100 - 240 264 vacrms v in frequency 47 60 50 63 hz i in 74 a (400w) parameter min nom. max unit v in 90 100 - 240 264 vacrms v in frequency 47 60 50 63 hz i in 84 a (450w) parameter min nom. max unit v in 90 100 - 240 264 vacrms v in frequency 47 60 50 63 hz i in 84 a (500w) parameter min nom. max unit v in 90 100 - 240 264 vacrms v in frequency 47 60 50 63 hz i in 10 5 a (550w) parameter min nom. max unit v in 103 115 240 264 vacrms v in frequency 47 60 50 63 hz i in 10 5 a (600w) parameter min nom. max unit v in 103 115 240 264 vacrms v in frequency 47 60 50 63 hz i in 10 5 a 1.1 inrush current limiting 50 a @ 115vrms 100 a @ 230vrms (at 25 o c ambient cold start). audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 1 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification ? 2. dc output 2.1 table 1. dc voltage regulation parameter range min nom. max unit +3.3v +/-5% +3.14 +3.3 +3.47 volts +5v +/-5% +4.75 +5.0 +5.25 volts +12v1 +/-5% +11.40 +12.0 +12.6 volts +12v2 +/-5% +11.40 +12.0 +12.6 volts -12v +/-10% -10.80 -12.0 -13.2 volts +5vsb +/-5% +4.75 +5.0 +5.25 volts 2.2 load ranges 2.2.1 table5 typical power distribution for a 300w atx12v configuration table5 typical power distribution for a 300w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 8.0 13.0 amps +12v2dc 0.5 - 11.0 13.0 amps +5vdc 0.2 - 15.0 - amps +3.3vdc 0.1 - 21.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q103w 2. total combined output of +12v1&+12v2 is Q216w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute requirements. 2.2.2 table5 typical power distribution for a 350w atx12v configuration audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 2 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification table5 typical power distribution for a 350w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 11.0 15.0 amps +12v2dc 0.5 - 14.0 18.0 amps +5vdc 0.2 - 15.0 - amps +3.3vdc 0.1 - 21.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q103w 2. total combined output of +12v1&+12v2 is Q265w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute requirements. 2.2.3 table5 typical power distribution for a 400w atx12v configuration table5 typical power distribution for a 400w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 18.0 19.0 amps +12v2dc 0.5 - 18.0 19.0 amps +5vdc 0.2 - 20.0 - amps +3.3vdc 0.1 - 24.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q120w 2. total combined output of +12v1&+12v2 is Q300w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute requirements. 4.when +12v1 & +12v2 load is over 20a,+5v min load is 0.5a 5. when +5v load is over 16a,+12v1 & +12v2 min load is 20a. 2.2.4 table5 typical power distribution for a 450w atx12v configuration audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 3 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification table5 typical power distribution for a 450w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 18.0 19.0 amps +12v2dc 0.5 - 18.0 19.0 amps +5vdc 0.2 - 20.0 - amps +3.3vdc 0.1 - 24.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q130w 2. total combined output of +12v1&+12v2 is Q350w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute requirements. 4.when +12v1 & +12v2 load is over 20a,+5v min load is 0.5a 5. when +5v load is over 16a,+12v1 & +12v2 min load is 20a. 2.2.5 table5 typical power distribution for a 500w atx12v configuration table5 typical power distribution for a 500w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 20.0 21.0 amps +12v2dc 0.5 - 20.0 21.0 amps +5vdc 0.2 - 20.0 - amps +3.3vdc 0.1 - 24.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q130w 2. total combined output of +12v1&+12v2 is Q360w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute 4. when +12v1 & +12v2 load is over 30a,+5v min load is 2.5a 2.2.6 table5 typical power distribution for a 550w atx12v configuration 550w cross regulation(5v rail +3.3v rail vs,12v) 5v +3.3v power(w) +12v power(w) cross loading graph for 550w configuraton audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 4 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification table5 typical power distribution for a 550w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 25.0 - amps +12v2dc 0.5 - 25.0 - amps +5vdc 0.2 - 24.0 - amps +3.3vdc 0.1 - 24.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q140w 2. total combined output of +12v1&+12v2 is Q420w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute 4. when +12v1 & +12v2 load is over 30a,+5v min load is 2.5a 2.2.7 table5 typical power distribution for a 600w atx12v configuration table5 typical power distribution for a 600w atx12v configuration parameter min nom. max peak unit +12v1dc 0.1 - 30.0 - amps +12v2dc 0.5 - 30.0 - amps +5vdc 0.2 - 24.0 - amps +3.3vdc 0.1 - 24.0 - amps -12vdc 0.0 - 0.3 - amps +5vsb 0.0 - 2.5 3.5 amps note: 1. total combined output of 3.3v and 5v is Q140w 2. total combined output of +12v1&+12v2 is Q 500w 3. peak currents may last up to 17 seconds with not more than one occurrence per minute requirements. 2.3 dc output ripple/noise. 2.3.1 talbe6 ripple regulation parameter ripple+noise unit +3.3v 50 mvp-p +5v 50 mvp-p +12v1 120 mvp-p +12v2 120 mvp-p -12v 120 mvp-p +5vsb 50 mvp-p 5v +3.3v power(w) +12v power(w) cross loading graph for 600w configuraton audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 5 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification 2.3.2 definition the ripple voltage of the outputs shall be measured at the pins of the output connector when terminated in the load impedance specified in figure 1. ripple and noise are measured at the connectors with a 0.1uf ceramic capacitor and a 10uf electrolytic capacitor to simulate system loading.ripple shall be measured under any condition of line voltage,output load,line frequency,operation temperature. 2.3.3 fignre3. ripple/noise voltage test circuit figure 3. ripple/noise voltage test circuit 2.4 overshoot any overshoot at turn on or turn off shall be less 10% of the nominal voltage value, all outputs shall be within the regulation limit of section 2.0 before issuing the power good signal of section 5.0. 2.5 efficiency power supply typical efficiency is 80% under full load at nominal input voltage of 115vac or 230vac. 2.6 remote on/off control when the logic level "ps-on" is low, the dc outputs are to be enabled. when the logic level is high or open collector, the dc outputs are to be disabled. ? 3. protection 3.1 over-power protection the power supply will be shutdown and latch off when output power is 110%~160%. 3.2 over voltage protection the over voltage sense circuitry and reference shall reside in packages that are separate and distinct from the regulator control circuity and reference.no single point fault shall be able to cause a sustained over voltage condition on any or all outputs.the supply shall provide latch-mode over voltage protection as defined in table. output minimum nominal maximum unit +12 v1dc or +12v2dc 13.4 15.0 17 volts +5 vdc 5.74 6.3 7.5 volts +3.3 vdc 3.76 4.2 4.8 volts 3.3 over current protection(300w) +5vdc' and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 14 30 a +12v2 13 30 a ac h o t ac neutral pow er supply v out v return 10uf 0.1uf load scope ac ground audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 6 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification 3.4 over current protection(350w) +5vdc'and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 16 34 a +12v2 19 34 a 3.5 over current protection(400w) +5vdc' and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 23 36 a +12v2 23 36 a 3.6 over current protection(450w) +5vdc',and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 23 36 a +12v2 23 36 a 3.7 over current protection(500w) +5vdc'and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 23 37 a +12v2 23 37 a 3.8 over current protection(550w) +5vdc'' and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 28 45 a +12v2 28 45 a 3.9 over current protection(600w) +5vdc' and '+3.3vdc' have separate over current protection circuits to meet 240va safety requirement. parameter min. max. unit +12v1 31 50 a +12v2 31 50 a no damage or hazardous condition should occur with all the dc output connectors disconnected from the load.the power supply may latch into the shutdown state. 3.10 over temperature protection(options) audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 7 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification 4. timing 4.1 signal timing drawing figure 4 is a reference for signal timing for main power connector signals and rails. figure 4. ps-ok timing sequence (1)t2: rise time (0.1ms~20ms) (2)t3: power good turn on delay time (100ms~500ms) (3)t4: power good turn off delay time (1ms min) (4)t5: rise time (10ms max) 4.2 .output transient response table 13. summarizes the expected output transient step sizes for each output. the transient load slew rate is =1.0a/us. table 13. dc out p ut transient ste p sizes max.step size max.step size output (% of rated output amps per sec 3.2.3) (1) (amps) +12 v1dc 40% +12 v2dc 60% +5 vdc 30% +3.3 vdc 30% -12 vdc 0.1a +5 vsb 0.5a '(1) for example,for a rated +5 vdc output of 18a,the transient step would be 30% x 18a=5.4a output voltages should remin within the remain within the regulation limits of section 2.1,and the power supply should stable when subjected to load transients per table 13. from any steady state load,including any or all of the following conditions: * simultaneous load steps on the +12 vdc,+5 vdc,and +3.3 vdc outputs (all steps occurring in the same direction) * load-changing repetition rate of 50 hz to 10 khz * ac input range per section 1.0 * +5vsb loading min 0.1a 4.3 hold up time (t6 of figure 4.) when the power loss its input power, the output shall maintain 16ms in regulation ranges at nominal input voltage. (ac:115v/60hz or 230v/50hz/90% load) when the power loss its input power, the output shall maintain 13ms in regulation ranges at nominal input voltage. (ac:115v/60hz or 230v/50hz/90% load) when the power loss its input power, the output shall maintain 10ms in regulation ranges at nominal input voltage. (ac:115v/60hz or 230v/50hz/90% load) 300w~500w 550w 600w audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 8 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification 4.4 capacitive load-required the power supply should be able to power up and operate with the regulation limits defined in table 15,with the following capacitances simultaneously present on the dc outputs. output capacitive loads output '+12v1dc '+12v2dc +5vdc +3.3vdc +5vsb -12vdc ? 5. environment 5.1 operation 0 o c to 40 o c 20 to 85%, non-condensing 5.2 shipping and storage -40 to 70 o c 5 to 90%, non-condensing 5.3 altitude 3,000ft max. 15,000ft max. 5.4 operating ac input voltage ac 90 ~ 264v auto ranging ac 103 ~ 264v auto ranging ? 6. safety 6.1 underwriters laboratory (ul) recognition. the power supply designed to meet ul 1950. 6.2 the power supply must be certified to en 60950-1:2006. 6.3 the power supply must bear the german bauart mark from tuv. 6.4 canadian standards association(csa) approval. the power supply designed to meet csa c22.2 no. 950. 6.5 semko,nemko,demko,fimko certified by any nordic . ? 7.0 electromagnetic compatibility (emc) 7.1 electrostatic discharge (esd) - en 61000 ? 4 - 2 1995 7.2 electrical fast transient / burst ( eft/b) ? en 61000 ? 4 - 4 ? 1995 7.3 surge ? en 61000 ? 4 - 5 1995 7.4 power frequency magnetic field ? en 61000 ? 4 - 8 1993 7.5 voltage dips ? rn 61000 ? 4 - 11 1994 7.6 radiated susceptibilty ? en 61000 ? 4 ? 3 1996 550w&600w 6000 storage operating temperature relative humidity temperature relative humidity 300w~500w capacitive load(uf) 10000 10000 10000 10000 330 audit:_________ ? ____________check:____________________design:____ ?[_____________ ATX0200(80plus).spec rev:30 9 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification 7.7 conducted susceptibilty ? en 61000 ? 4 - 6 1996 7.8 voltage fluctation - en 61000 ? 3 ? 3 1995 7.9 en61000-3-2 harmonic current emissions. if applicable to sales in europe, the power supply shall meet the requirements ofen 61000-3-2 class d and the guidelines for the suppression of harmonics in appliances and general use equipment class d for harmonic line current content at full-rated power. 7.10 en 55022:2006+a1:2007 class b radio interference. 7.11 fcc part 15 class b 115vac operation. ? 8. mtbf 8.1 mtbf (mean time between failures) calculation the demonstrated mtbf shall be 100,000 hours of continuous operation at 25 o c,full load, 80% confidence limit and nominal line. the mtbf of the power supply shall be calculated in accordance with mil-std-217d/e. the dc fan is not included. 9. mechanical requirements 9.1 physical dimension ?M??L?H???? la audit:_________ ? ____________check:____________________design:____ ?[_____________ ATX0200(80plus).spec rev:30 10 of 11 2010/04/15
enhance electronics co.,ltd ________________________________________________________________________________________________________ product specification 9.2 connectors (intel approved equivalent) p1 connector (molex 39-01-2240 or equivalent) 18awg wire signal pin pin signal 18awg wire orange +3.3v 11 1 +3.3v orange orange(22awg) 3.3 sense 11 blue -12vdc 12 2 +3.3v orange black com 13 3 com black green(20awg) ps-on 14 4 +5vdc red black com 15 5 com black black com 16 6 +5vdc red black com 17 7 com black white nc 18 8 pok grey(20awg) red +5vdc 19 9 +5vsb purple red +5vdc 20 10 +12v1dc yellow red +5vdc j3 j1 +12v1dc yellow black com j4 j2 +3.3vdc orange p2 connector(molex 39-01-2040 or equivalent) 18 awg wire signal pin pin signal 18awg wire black gnd 1 3 yellow/black stripe +12v2 black gnd 2 4 yellow/black stripe +12v2 p3,p4,p5,p6,p7,p8,p9(amp 1-480424-0 p12,p16 (amp 171822-4 or equivalent) or molex 8981-04p or equivalent) 18 awg wire signal pin pin signal 20awg wire yellow +12v1 1 1 +5vdc red black com 2 2 com black black com 3 3 com black red +5v 4 4 +12v1 yellow p10,p11,p12,p13 (optional) sata power connector (molex* 88751 or equivalent) 18 awg wire signal pin orange +3.3v 5 black gnd 4 red +5v 3 black gnd 2 yellow +12v1 1 10. options 10.1 fan speed control main fan voltage varies with the ambient temperature or output power. audit:_________ ____________check:____________________design:____ _____________ ATX0200(80plus).spec rev:30 11 of 11 2010/04/15

▲Up To Search▲

Price & Availability of ATX0200

	To Download ATX0200 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .